If it is a design flaw, shouldn’t there be a recall program? Fewer chrome tabs, smaller rendering jobs.
![late 2017 mac pro lcd screen late 2017 mac pro lcd screen](https://t5h6g9t7.stackpathcdn.com/wp-content/uploads/2021/01/A1419-A2115-display-panel-768x768.jpg)
For better airflow and ventilation, keep the MacBook on a table or a hard surface.
#Late 2017 mac pro lcd screen install#
#Late 2017 mac pro lcd screen free#
If your device is still under warranty, you’re in luck! For a free replacement, walk in to an Apple Authorized Service Provider ( there are a number of fake AASPs around, careful!). Follow that, and you can almost certainly avoid recurrence. Read the What can I do to avoid this? section below. But, now, with this new-found knowledge, you can proactively avoid any overheating in your MacBook. Unfortunately, yes, you do run that risk. “If it is a design flaw, won’t my new display also get damaged?” you ask? Good question. So, display assembly replacement is the only real, sure-shot solution. The T-CON board is attached to the display assembly, and there’s no way to replace the board alone. Yes, but it is expensive - getting the display replaced. This leads to insufficient heat management, ergo higher chances of conking off. Simple - the 13 inch non Touch Bar model (A1708) has a single internal Fan, while most of the other MacBook Pro models 2016 onwards, have two (don’t ask why!). Why is the 13 inch non Touch bar model 2016-17 especially vulnerable? For more discussion around it check this and this. This could be triggered by clogged or malfunctioning fans, dust build-up in the heatsink fins, or even poor air circulation around the MacBook (think using MacBook on a pillow).ĭisclaimer: Please be informed that this explanation is offered by independent experts (hat tip to Mr Dan at iFixit). There is hardly any air circulation in the T-CON board compartment, making it extremely vulnerable to damage from overheating. It is mounted very close to the heatsink radiator. 2016 onwards, this board, while still being connected to the display, sits inside the top case or main chassis (read: keyboard panel). It was part of the “lid”, removed from the main chassis. Up until 2015 this board used to be tucked inside the hinge cover at the bottom edge of the display. All MacBook displays have a small logic board of their own. Poor thermal management leads to the display logic board (T-CON board) getting cooked from overheating. It is believed to be a design flaw from Apple. There is a technical explanation for this. However, in our experience here at Fixxo, the 13 inch MacBook Pro non Touch Bar model 2016-17 (Model A1708) is the most frequently impacted model. MacBooks with Apple M1 chips are considered safe. These include 13 inch, 15 inch, even 16 inch devices. Technically, all MacBook Pro models launched after 2016, with an Intel CPU chip inside, would be vulnerable to this issue. Read about it here: Flexgate: MacBook Pro display backlight issue - Is it repairable? Which MacBooks are impacted?
![late 2017 mac pro lcd screen late 2017 mac pro lcd screen](https://images.unionrepair.com/images/watermarked/1/detailed/32/17852-full-lcd-screen-assembly-for-macbook-pro-13-a706-a1708-late-2016-mid-2017-4.jpg)
![late 2017 mac pro lcd screen late 2017 mac pro lcd screen](https://c1.neweggimages.com/ProductImage/AGXMD200917G0CCH.jpg)
Although both impact the same MacBook models, that issue is actually entirely different.
![late 2017 mac pro lcd screen late 2017 mac pro lcd screen](https://macblowouts.com/wp-content/uploads/2019/05/IMG_7426-scaled.jpg)
Note: Is your MacBook display showing Stage Light Effect - alternatively bright & dim areas along the bottom of the display? Or is it going blank when you open the lid beyond a certain angle? If yes, it is not a T-CON board issue. In the worst case scenario, the entire screen is covered with lines rendering the device unusable. In early stages, it may be completely reversible. This of course depends on how far damaged it is.